Forum Replies Created
-
AuthorPosts
-
v1ntageMemberQuote:I happen to have a V4 case with no circuit board, so yes, I would be.
Sounds like a good match!
Presumably you are handy with a soldering iron too?
Want to Make me an offer?
Can send a photo if I have an email address.
Simon
v1ntageMemberQuote:Hi….. Obviously you still feel that amount is not enough… Can you please tell me what you’re looking for for this board. Without the SAD BBD it’s lost a lot of value, in fact a good 75% of the value is in that chip which I don’t want. The rest of the components are all still available, and cost pence, so no value in resistors or the other IC’s.Looking at the photos I have of this board it appears that some version 2’s had all the IC’s soldered directly to the board except the SAD1024… In another photo of another v2 board they’re in DIL sockets…. Either way the SAD chip will pop out as it’s likely in a DIL socket.
I’m already making a mistress clone, but want to make a a more accurate one in line with the original layout. I did exactly the same with the colorsound Power boost pedal, and in fact stu Castledine complimented me on my PCB fabrication, and how accurate it was to his.
I want this board… But at a reasonable price, ‘cos at the end of the day we both know what a PCB is worth….. not a lot in all honesty. Please let me know how much you’d let it go for…. Or you may just end up sitting on it for another 2 years.
Well yes, £30 isnt quite worth it. And honestly I could rack it & use it but a lot of my output is via modellers these days. That said the model of the Mistress doesnt hold a candle to the original analogue device… there’s a broad consensus on that. The E M does have a very distinctive tone – as you know…
Yes, you are correct – the BBD is in a DIL socket , as is the CMOS 4013. Board is printed EH 5200-1 and then M (I think ) P underneath that.
OK, for the sake of a deal £50 including delivery to your UK address with SAD 1024 extracted.
I will need an email address if you want it.SImon
v1ntageMemberQuote:Sorry if that price was way under your initial expectation…… I understand that was maybe too low.Are you willing to sell it separate from the SAD1024 chip? If not, instant message me how much you want for it as is….
I have no particular problem extracting the BBD and detaching the pcb (I am a trained electronic engineer) as is but I would need to see an amount that made that worthwhile and it would be quite a bit more than £15.
Apologies but it really just isnt worth the bother at anything like that money but don’t blame you for asking!
Are you UK?v1ntageMemberQuote:I’m not interested in the 1U rack… and believe it or not I’m not interested in the SAD1024…… I have 2 NOS chips already.I’m really only interested in the board… Nothing else. If you want to remove the SAD1024 chip and sell that on EBay separately go ahead… you should get around £70 for that chip on its own.
I’ll give you £15 + shipping cost for the board without the chip, pots, and 1U rack….
Andy
No thanks.
v1ntageMemberQuote:I would like to buy it….. How much do you want for it??Instant message me and i’ll give you my email
Many thanks
Andy
Fair enough. Not sure how much its worth – the SAD1024 itself is worth a few £.
Do you want it as it is mounted to a 1U rack panel or just the board and pots?
Can put it on eBay if you wish.
Make me an offer?v1ntageMemberQuote:Quote:Hi,Rummaging around my old gear I found an original circuit board for the black/green Electric Mistress The pcb is marked rev EH-5200-1 so the first and earliest version made in this livery dating back to around 1977. It uses the Reticon SAD 1024 of course and matches the original circuit diagram spec.
Perhaps foolishly in hindsight I junked the original casing and 19″ 1U rack mounted it with access to all controls including providing cv input. I used the original pots. I believe it works perfectly.
Anybody interested in buying it? Can provide pics and further detail on request.
May eBay it. I am UK based.It’s a punt after so long….. But have you still got this PCB, and if so do you still want to sell it?
It actually is! Never did anything much to try selling it bar the mention here.
If you are interested let me know.Simon
v1ntageMemberQuote:I might be interested depending on the price, send me a PM.PM Sent (hopefully?)
-
AuthorPosts
