Forum Replies Created
-
AuthorPosts
-
EHX STAFFKeymaster
HOG 1 US9LDC-500 UK9LDC-500 EU9LDC-500 9vdc, 500mA center positive
HOG 2 US96DC-200BI UK96DC-200BI EU96DC-200BI 9.6vdc, 200mA
EHX STAFFKeymasterThe HOG 1 and Hog 2 use different power supplies..
Please write the techs on Monday at info@ehx.com
they can help you. If you do not hear back please check your spam folder.EHX STAFFKeymasterThank you!
EHX STAFFKeymasterPlease write the techs on Monday they can help you out!
info@ehx.comEHX STAFFKeymasterSorry!
Please check you spam folder as it might be there. They write everyone back
If not please write again after the holiday as they are closed now. info@ehx.com
If you dont hear back from them, come back here and I will make sure its there.- This reply was modified 2 years, 11 months ago by EHX STAFF.
EHX STAFFKeymasterWe have one that does that called the Inteligent Harmony Machine:
EHX STAFFKeymasterYou can use it as that with two of the outputs on the switcher:
CTRL 1 Footswitch:
• The CTRL 1 footswitch can be used to switch amp channels, trigger
remote effects etc.
• CTRL 1 can be set normally open or closed.
• CTRL 1 can be set to momentary or latching.
• CTRL 1 can be set as a master bypass button.
CTRL 2 Footswitch:
• The CTRL 2 footswitch can be used to switch amp channels, trigger
remote effects, etc.
• CTRL 2 can be set to normally open or closed.
• CTRL 2 can be set to momentary or latching.EHX STAFFKeymasterEHX STAFFKeymasterIts at the bottom of page 7 in the manual
You can also disable the internal footswitch’s tap tempo function. This is
useful when you want to turn the pedal on/off very quickly. To
disable/enable internal tap tempo, unplug power from the CANYON, press
and hold the footswitch, then plug power back in while holding the
footswitch. The LED will slowly blink five times if tap tempo is turned off,
and will blink twice if tap tempo is turned on. The CANYON saves your tap
tempo enable/disable setting until it is changed again, even if the pedal is
removed from power. Tip: If you set the Tails switch to ON and disable
internal tap tempo, you can quickly switch the CANYON in and out of effect
mode to “grab” individual notes or phrases to repeat, or to keep high
FEEDBACK settings from becoming too busy.
You can also reset the internal footswitch’s tap tempo to the factory setting
of enabled by holding the footswitch when resetting secondary knob
settings. See step 11 in “Using Secondary Knob Mode” below.- This reply was modified 2 years, 11 months ago by EHX STAFF.
EHX STAFFKeymasterPlease write the techs at info@ehx.com
They can help you.EHX STAFFKeymasterPlease post your question in the vintage section. People will help you there.
EHX STAFFKeymasterPlease check your spam folder as everything gets answered that comes in. I will pass this on in case.
December 9, 2021 at 10:38 am in reply to: EHX canyon tap tempo only works for a couple seconds HELPE PLEASE! #186617EHX STAFFKeymasterPlease write the techs at info@ehx.com
December 8, 2021 at 6:22 pm in reply to: Electro-Harmonix Introduces the Intelligent Harmony Machine Pedal #186615EHX STAFFKeymastermvax2 The pedal setting is shown in the video at 7:40 in.
EHX STAFFKeymasterMike please write the techs at info@ehx.com about this. There maybe a firmware fix for this.
-
AuthorPosts
