Forum Replies Created
-
AuthorPosts
-
EHX STAFFKeymasterEHX STAFFKeymaster
Its at the bottom of page 7 in the manual
You can also disable the internal footswitch’s tap tempo function. This is
useful when you want to turn the pedal on/off very quickly. To
disable/enable internal tap tempo, unplug power from the CANYON, press
and hold the footswitch, then plug power back in while holding the
footswitch. The LED will slowly blink five times if tap tempo is turned off,
and will blink twice if tap tempo is turned on. The CANYON saves your tap
tempo enable/disable setting until it is changed again, even if the pedal is
removed from power. Tip: If you set the Tails switch to ON and disable
internal tap tempo, you can quickly switch the CANYON in and out of effect
mode to “grab” individual notes or phrases to repeat, or to keep high
FEEDBACK settings from becoming too busy.
You can also reset the internal footswitch’s tap tempo to the factory setting
of enabled by holding the footswitch when resetting secondary knob
settings. See step 11 in “Using Secondary Knob Mode” below.- This reply was modified 2 years, 7 months ago by EHX STAFF.
EHX STAFFKeymasterPlease write the techs at info@ehx.com
They can help you.EHX STAFFKeymasterPlease post your question in the vintage section. People will help you there.
EHX STAFFKeymasterPlease check your spam folder as everything gets answered that comes in. I will pass this on in case.
December 9, 2021 at 10:38 am in reply to: EHX canyon tap tempo only works for a couple seconds HELPE PLEASE! #186617EHX STAFFKeymasterPlease write the techs at info@ehx.com
December 8, 2021 at 6:22 pm in reply to: Electro-Harmonix Introduces the Intelligent Harmony Machine Pedal #186615EHX STAFFKeymastermvax2 The pedal setting is shown in the video at 7:40 in.
EHX STAFFKeymasterMike please write the techs at info@ehx.com about this. There maybe a firmware fix for this.
EHX STAFFKeymasterShoe Please send the video and info to the techs at info@ehx.com
They can help you!EHX STAFFKeymasterPlease check you have erased the loop first:
ERASING A LOOP
1. To erase a loop, playback must be stopped. If a loop is playing, press
the footswitch two times quickly to stop it.
2. Press and hold the footswitch for 2 seconds to erase the loop memory.
The LED will blink red six times then remain off, indicating that the
loop is erased.
3. Note: the ERASE function is only available when the loop has
recorded memory, as indicated by the dim green LED.EHX STAFFKeymasterMike which looper pedal are you using?
December 1, 2021 at 8:36 pm in reply to: Nano Deluxe Memory Man LFO ticking noise – return, or is this fixable? #186419EHX STAFFKeymasterHi Ryan
Please write the techs tomorrow at info@ehx.com They can help you out.November 25, 2021 at 9:46 am in reply to: Super Switcher volume loss intermittent but unacceptable also unit freezes up! #186330EHX STAFFKeymasterThey can fix it fast. Something is wrong with yours or the supply is bad.
If you have not heard back check your spam folder as Robyn writes EVERYONE back.
It is the thanksgiving holiday here and the factory is closed until Monday. People are with their family’s
Dont worry you will get it fixed!November 25, 2021 at 9:41 am in reply to: Buggy EHX Oceans 12 pedal goes silent – spring reverb mode C does not exist! #186329EHX STAFFKeymasterGood. Most problems point back to power supply issues. 1spot is often the cause. Also keep in mind when many pedals are used in a daisy chain the supply’s available current drops They then wind up staving the pedals for current.
November 22, 2021 at 7:42 pm in reply to: How to set Japanese Banjo sound on Attack Decay pedal performed in YouYube #186257EHX STAFFKeymasterHi This is Bill Ruppert. I did the demo.
The sound is the setting shown. The only effect is a room reverb after the pedal.
The Superego was just for the backing chord.
I used the bridge pick up or the split coil sound for a nice bright tone. Also pick closer to the bridge. That gives it even more twang.
Make sure your amp is set very clean.
If you can make a video of you playing it and I can try and I will help you dial it in. It does not have to be a great video just something to help me hear what you are doing.
Thanks Bill -
AuthorPosts