Forum Replies Created
-
AuthorPosts
-
July 28, 2022 at 8:20 pm in reply to: Guitar Synth sound settings in the Attack Decay demo by Bill Ruppert #192014EHX STAFFKeymaster
Ohm Thanks
I bet you can get it.
Are you sure the Harmonix knob is at zero?
If not can you send a mp3 or wav recording to info@ehx.com
Have them forward to me. I will see if I can help.
BillJuly 26, 2022 at 3:10 pm in reply to: Guitar Synth sound settings in the Attack Decay demo by Bill Ruppert #191999EHX STAFFKeymasterOhm
The settings shown are correct, but there is a lot of ways it can sound different.
1. Make sure none of the three preset LEDS are on. Otherwise the knobs will not be correct.
2. Make sure the “poly” led in ON.
3. Make sure the red “harmonix” led is on. Its above the left footswitch.
4. Use the neck pickup on your guitar. I have humbuckers.Hope that helps.
Bill- This reply was modified 2 years, 4 months ago by EHX STAFF.
EHX STAFFKeymasterPlease write the techs at info@ehx.com
They can help you out fast.EHX STAFFKeymasterBaron the way you are using it going in front of the amp is best. It sounds more natural. if the blend is 100% effect you should not hear the original signal.
BUT you will still hear it in the air as the guitar is close to your ears. Try recording it to see if you still hear the dry signal.EHX STAFFKeymasterPlease write the techs at info@ehx.com
They can help you out!EHX STAFFKeymasterSorry we are still 3-4 months out.
EHX STAFFKeymasterGerry
BYPASS MUTE Internal DIP Switch Inside the STRING9 is a small DIP switch
labeled dry/mute. This switch allows you to choose the signal output from the
EFFECT jack when the STRING9 is in bypass mode.
While the STRING9 is in Bypass, and the DIP switch is set to dry (factory
default), the EFFECT jack outputs the signal present at the INPUT. This is the
standard guitar pedal routing for bypass. Set the DIP switch to mute, and– 2 –
Controls and Connections
the EFFECT jack output is muted in bypass. This is handy when sending the
STRING9’s string effects to a different amplifier or mixer channel and you
don’t want to hear your guitar out of that amp while in bypass.
To change the dry/mute DIP switch setting, do the following:
Remove the bottom cover of the STRING9.
Locate the small board with the footswitch and ribbon cable. Here you’ll
find the DIP switch labeled dry and mute.
Change the dry/mute DIP switch setting with a small flathead screwdriver.
Note: this switch is very delicate. Do not force it when changing settings.
If the switch handle doesn’t move easily, try moving it the other way first
and then back to the position you want.You can always write the techs at info@ehx.com
EHX STAFFKeymasterBehn Please write the techs at info@ehx.com
They can help you out.EHX STAFFKeymasterPlease write info@ehx.com
EHX STAFFKeymasterSorry!
Please write the techs at info@ehx.com
They can help you out.EHX STAFFKeymasterHi Tomasz
Yes you can send to three different amps using just the send outs.EHX STAFFKeymasterSorry to hear this.
Please write the techs at info@ehx.com.
They can help you.
If you get nothing with all sliders being moved it is best to exchange for a new one for the dealer you bought it from.
Again sorry!May 29, 2022 at 1:31 pm in reply to: MOD 11 – How does it WORK? Why do the lights blink? WTF? Instructions useless. #190960EHX STAFFKeymasterPlease write info@ehx.com
EHX STAFFKeymasterPlease write the techs at info@ehx.com
EHX STAFFKeymasterSorry
The techs can fix this fast and cheap.
Please write info@ehx.comIf you do not hear back please, check your spam folder as some times things wind up there.
-
AuthorPosts
