Forum Replies Created

Viewing 15 posts - 166 through 180 (of 2,047 total)
1 2 3 … 11 12 13 … 135 136 137
  • Author
    Posts
  • August 17, 2022 at 2:50 pm in reply to: distortion #192366
    EHX STAFF
    Keymaster

    Sorry no idea what product you are talking about.
    Please write the techs at:
    info@ehx.com

    August 17, 2022 at 2:45 pm in reply to: Guitar Synth sound settings in the Attack Decay demo by Bill Ruppert #192365
    EHX STAFF
    Keymaster

    Thanks Ohm
    I had a listen.
    First That sound I did is for solo sounds only. it will not work for chords.
    Second, something is wrong as it sounds like you’re not driving the pedal hard enough.
    I can’t even hear the effect, it’s just dark.
    Turn up the sensitivity knob and make sure the poly light is on.
    Your going to have to adjust things to work as it’s not being driven hard to open the envelope..

    August 15, 2022 at 12:48 pm in reply to: Guitar Synth sound settings in the Attack Decay demo by Bill Ruppert #192340
    EHX STAFF
    Keymaster

    Ohm
    I am sorry they told me your mail did not go through. Please try again and put For Bill Ruppert in the header.
    You could also throw it up on youtube as well and post the link here.

    August 8, 2022 at 6:20 pm in reply to: Compression setup for Mel9 #192100
    EHX STAFF
    Keymaster

    To control peak’s place the compression after the Mel9.
    Set it clean and use only enough to remove the loud spikes.
    The pic at the top of the page shows a setting that should work:

    Platform

    Another trick is to simply lower the volume on the mel9, so you have to dig in a little to get max volume.

    August 8, 2022 at 6:12 pm in reply to: Super Switcher volume loss intermittent but unacceptable also unit freezes up! #192099
    EHX STAFF
    Keymaster

    Please write the techs at info@ehx.com
    Check your spam folder if you do not hear back

    August 1, 2022 at 6:38 pm in reply to: Guitar Micro-Synth On, But No Sound #192038
    EHX STAFF
    Keymaster

    Paul Please write the techs at info@ehx.com

    August 1, 2022 at 6:37 pm in reply to: Microsynth Bass Not Working #192037
    EHX STAFF
    Keymaster

    Could be a dirty switch. Please write the techs at info@ehx.com

    July 31, 2022 at 3:36 pm in reply to: Guitar Synth sound settings in the Attack Decay demo by Bill Ruppert #192031
    EHX STAFF
    Keymaster

    Yes that looks right.
    blend is at max.
    Make sure the amp is set very clean.
    Use the neck pickup
    Make sure you are not overdriving the amp into distortion.

    July 28, 2022 at 8:20 pm in reply to: Guitar Synth sound settings in the Attack Decay demo by Bill Ruppert #192014
    EHX STAFF
    Keymaster

    Ohm Thanks
    I bet you can get it.
    Are you sure the Harmonix knob is at zero?
    If not can you send a mp3 or wav recording to info@ehx.com
    Have them forward to me. I will see if I can help.
    Bill

    July 26, 2022 at 3:10 pm in reply to: Guitar Synth sound settings in the Attack Decay demo by Bill Ruppert #191999
    EHX STAFF
    Keymaster

    Ohm
    The settings shown are correct, but there is a lot of ways it can sound different.
    1. Make sure none of the three preset LEDS are on. Otherwise the knobs will not be correct.
    2. Make sure the “poly” led in ON.
    3. Make sure the red “harmonix” led is on. Its above the left footswitch.
    4. Use the neck pickup on your guitar. I have humbuckers.

    Hope that helps.
    Bill

    • This reply was modified 2 years ago by EHX STAFF.
    July 26, 2022 at 2:47 pm in reply to: Issue with input and polarity #191995
    EHX STAFF
    Keymaster

    Please write the techs at info@ehx.com
    They can help you out fast.

    July 18, 2022 at 7:02 pm in reply to: Pitch Fork into high gain amp? #191793
    EHX STAFF
    Keymaster

    Baron the way you are using it going in front of the amp is best. It sounds more natural. if the blend is 100% effect you should not hear the original signal.
    BUT you will still hear it in the air as the guitar is close to your ears. Try recording it to see if you still hear the dry signal.

    July 7, 2022 at 8:59 pm in reply to: HELP MEMORY BOY ONLY DRY SIGNAL OUTPUT #191575
    EHX STAFF
    Keymaster

    Please write the techs at info@ehx.com
    They can help you out!

    June 25, 2022 at 1:57 pm in reply to: MIG 50s Where Are They? #191392
    EHX STAFF
    Keymaster

    Sorry we are still 3-4 months out.

    June 18, 2022 at 8:26 pm in reply to: Synth9 dry knob not working #191350
    EHX STAFF
    Keymaster

    Gerry
    BYPASS MUTE Internal DIP Switch Inside the STRING9 is a small DIP switch
    labeled dry/mute. This switch allows you to choose the signal output from the
    EFFECT jack when the STRING9 is in bypass mode.
    While the STRING9 is in Bypass, and the DIP switch is set to dry (factory
    default), the EFFECT jack outputs the signal present at the INPUT. This is the
    standard guitar pedal routing for bypass. Set the DIP switch to mute, and

    – 2 –

    Controls and Connections

    the EFFECT jack output is muted in bypass. This is handy when sending the
    STRING9’s string effects to a different amplifier or mixer channel and you
    don’t want to hear your guitar out of that amp while in bypass.
    To change the dry/mute DIP switch setting, do the following:
    Remove the bottom cover of the STRING9.
    Locate the small board with the footswitch and ribbon cable. Here you’ll
    find the DIP switch labeled dry and mute.
    Change the dry/mute DIP switch setting with a small flathead screwdriver.
    Note: this switch is very delicate. Do not force it when changing settings.
    If the switch handle doesn’t move easily, try moving it the other way first
    and then back to the position you want.

    You can always write the techs at info@ehx.com

  • Author
    Posts
Viewing 15 posts - 166 through 180 (of 2,047 total)
1 2 3 … 11 12 13 … 135 136 137