- This topic has 12 replies, 5 voices, and was last updated 7 years, 2 months ago by Sylus.
-
AuthorPosts
-
September 18, 2017 at 9:05 pm #85004gvelascoParticipant
Curse you electro-harmonix! Now, this is the one I need.
September 18, 2017 at 10:18 pm #123165mchadMemberNice one EHX!
Now, Superego+ plus the 8 Step? What will happen?
September 19, 2017 at 2:32 am #123167gvelascoParticipantQuote:Nice one EHX!Now, Superego+ plus the 8 Step? What will happen?
Ooh.
September 19, 2017 at 3:01 am #123168julianModeratorQuote:Nice one EHX!Now, Superego+ plus the 8 Step? What will happen?
Pure sonic mayhem since it appears that you can simultaneously control every control via CV with the expression presets and you can also gate the effect via the footswitch jack.
Quote:SETTING EXPRESSION PEDAL PRESETS
Program and save EXP pedal presets by executing the following steps:
1. Insert an expression pedal into the EXP jack.
2. Tap the EFFECT footswitch, if necessary, to ensure that the effects are off.
3. Press and hold the EFFECT footswitch for more than one second. The green Effects LED will start to blink.
4. Release the EFFECT footswitch.
5. Set the expression pedal to heel-down and set the 7 controllable knobs (ATTACK, DECAY, RATE, DEPTH, THRESHOLD, LAYER and GLISS) to the desired heel-down setting.
6. Put the expression pedal in toe-down position and set the same 7 knobs to the desired toe-down setting. If you do not want a knob to change with the expression pedal then do not turn it during this step.
7. NOTE: The expression pedal must be placed into the heel-down and toe-down positions at least once during preset acquisition.
8. Press and hold the EFFECT footswitch.
9. The Effects LED will flash red to confirm that a preset has been saved. The Red LED will only light with an expression pedal plugged into the EXP jack.
10. Release the EFFECT footswitch, the red LED goes solid. The solid red LED indicates that an expression pedal preset has been saved and is active.MORE ABOUT EXPRESSION PEDAL PRESETS
• To exit programming an expression pedal preset without saving changes, press and release the EFFECT footswitch at any time before step 8 in the above procedure.
• When a preset is active, turning any of the 7 control knobs will save that knob’s new setting as both the heel-down and toe-down setting. The EFFECTS LED will flash red for half a second and then remain lit solid.
• To erase a preset, make sure the EFFECTS are off. Press and hold the EFFECTS footswitch for 5 seconds. After one second the green LED will begin flashing. After 5 seconds the green LED will flash quickly. Release the EFFECTS footswitch and the preset will be cleared. The EFFECTS LED will light green and the expression pedal controls the default parameter.Question for EHX:
“When a preset is active, turning any of the 7 control knobs will save that knob’s new setting as both the heel-down and toe-down setting. The EFFECTS LED will flash red for half a second and then remain lit solid.”
Say I have a preset and I change one knob in this fashion then switch away and come back. Will that change still be in effect or was it temporary?
Also. . . is there a way to switch to the FX default expression setting without erasing the preset?
September 19, 2017 at 4:04 am #123172September 20, 2017 at 3:07 am #123174julianModeratorSo say I have an expression pedal preset saved for the mod effect with toe/heel positions set for all seven knobs. The manual says that if I tweak one of those knobs it will set both the toe and heel position for that knob to your new knob position. Let’s say I tweak the glissando knob while playing with this setting. Can I get my original preset back by switching to delay and switching back to mod? Or when I switch back will it remember the change I made to the glissando knob?
September 20, 2017 at 2:20 pm #123178EHX STAFFKeymasterJulian your settings are store. You would need to erase that preset:
It is in the manual link above.September 20, 2017 at 2:21 pm #123179EHX STAFFKeymasterWOW anything is possible
Quote:Nice one EHX!Now, Superego+ plus the 8 Step? What will happen?
September 20, 2017 at 9:15 pm #123182julianModeratorQuote:Julian your settings are store. You would need to erase that preset:
It is in the manual link above.I read through the manual, I’m just not really clear on that one point. It says that altering the knobs while the preset is up changes the toe/heel settings for that knob on the preset. Is that temporary until I bring up the preset again, or have I altered the preset until I erase & reprogram?
September 20, 2017 at 11:08 pm #123183mchadMemberHow about double Super?
Superego+ PLUS Super Pulsar.
The Hold function in conjunction with trem can be spectacular.
September 26, 2017 at 9:36 pm #123198SylusMemberQuote:Quote:Julian your settings are store. You would need to erase that preset:
It is in the manual link above.I read through the manual, I’m just not really clear on that one point. It says that altering the knobs while the preset is up changes the toe/heel settings for that knob on the preset. Is that temporary until I bring up the preset again, or have I altered the preset until I erase & reprogram?
Can someone please tell me the dimensions of this pedal? I cannot this info anywhere. It would be a big help in figuring out the pedal board lay out. Thanks
September 30, 2017 at 5:23 pm #123209EHX STAFFKeymasterL 6.5
W 4.5
D 1.5October 4, 2017 at 1:16 am #123216SylusMemberThank you.
With the ever increasing popularity of pedal boards and the desire to fit more on them, I wish all pedal makers would include the full spec’s of their products in their AD copy and websites. -
AuthorPosts
- You must be logged in to reply to this topic.
